Search results

Responding too! I'll look this weekend as I have a complete set-up still in the box and I'll get the prt number off it (in case any new guys are still interested).

Does ASHAM still exist?

Ok, long story short, my '97 Base took a header into a guardrail (on the drivers side nose) at 35mph roughly 3 years ago. car has been down from them on, while I searched for replacement panels. My question/question: After the accident, my ABS light stays on and my odometer is dashed out (plus...

Being I am swapping to C-heads, my question is: Will the '03-'05 Aviator intake fit under the hood of a Gen2? I am assuming NO as it is considerably taller than both the 96-98 Cobra intake and the 99-01 Cobra/03-04 Mach1 intakes. Also, I know the top plate of the aviator would need to be...

Up for sale is a 1996 Cobra intake manifold. It didn't have a throttle cable bracket on it when I got it and it leaves the same way. It does come with the FelPro 3-piece intake gasket set (lid and intake-to-IRMC gaskets). $300 plus shipping (obo). I am shipping from St.Cloud, Florida (and...

I have 3 factory HID bulbs in working order, $125 shipped. PayPal accepted.

Guys, do any of you happen to have access to the wiring diagram/pin call-out for the 2000-02 LS clockspring? I am looking for the wiring for the two large plugs (the Black and the Gray plugs) and what those pins/wires run to. I have a project going that will require me knowing so that I can...

Guys, I know this is asking a LOT and I am sorry. I have a complete 1997 clockspring module and I was wondering what the pin-out was for the two large (one Black, one Gray) connectors is? I know the last one is AIRBAG (the small two-wire unit). I need to know what the pins are hooked to on the...

Anyone have any idea of how to adjust a door (on my 97 Base)? I need to slide my drivers door back to get it aligned properly. Hopefully I will be able to loosen the door-to-body hinge bolts and slide the door back. Once I get that done, I can hang my fender and get my nose squared up...

Ok, so the 97-98 MKVIII can tell if you have a light out and report back to you. This is called the CAN-BUS system, correct? The 94 back-half I have grafted to my 97 front half works great with regular old 3157/3457 bulbs. As soon as I install LEDs in the brake/turn/park position, the 'Check...

After bouncing the car off a guardrail (see 'Members Rides for that description of no fun) earlier this year and now getting it put back together, I am curious if the dash airbag unit (mine went off) can be removed/replaced or if the entire dash has to be removed/replaced. The vehicle in...

Ok guys; what is the plunger-type switch looking thing (passenger side front underhood close to the air box) under the hood and what does it do? I see it is a two-wire and is connected/routed in with the MAF wiring. It looks like it could be an underhood service light switch, except there is no...

After some searching, I have come up with 'The Puddle Lamps come on when you unlock the doors or use the remote/keypad'. While this sounds pretty straight-forward, I do have a question related to their function. Mine do not work on my 97 Base, and both bulbs are good, along with the fuse...

Some steering rack ratio info: As per thecarconnectioncom: Rack ratios: Lock-To-Lock turns: 1989-97 MN12 platform and 93-96 MKVIIIs: 14.10:1...

Does anyone know how closely the Strutmaster front struts mimic the rebound/load rate of the original air strut? Are they comparable in compression and rebound pressure rates? Which holds the higher rate if one is superior to the other? Reason I am asking is there are two MKVIIIs here in a...

Does anyone know if the air bag is able to be separated from the strut? Are the bags replaceable without having to get a complete air strut assembly?

Cruising the 'search' function for answers, I see a ton for the Gen1 cars...........not so much for the Gen2 cars. The OD disengage button hasn't worked on my 97 since I got it. Any ideas on how this gets fixed on the Gen2 rides? And am I correct in thinking the shift knob comes off by way of...

Anybody know if these cars suffer from bumpsteer when lowered past 1.5"? If so, would anyone happen to know if the outer tie-rod end swivel has the same taper as the 94+ Mustang unit (thus allowing the use of an aftermarket Bumpsteer kit meant for a Mustang)?

Well, this morning started out bad. Wrecked the Lincoln on the way to work; spun at 80mph (car did an immediate left after I passed a vehicle) and went for a thrill-ride of trying to NOT hit anyone around me. After a few direction changes and a LOT of tire smoke, I ended up in the center (wet...

Would it be possible to fit AOD-E overdrive gearing into the 4R70w? Being the overdrive comes in at .667:1 versus the .70:1, I was wondering if it could be done to gain back a small margin of overdrive when going to steeper rear end gears.