windshield washer motor removal?
- Thread starter 94 Mark 8
- Start date
RE: windshield washer motor removal?
The manual says:
__________________
Windshield Wiper Motor
When installing the drive arm to a new windshield wiper motor follow the instructions included in the new windshield wiper motor kit.
CAUTION:
The internal permanent magnets used in the windshield wiper motor are a ceramic (glass-like) material. Care must be exercised in handling the windshield wiper motor to avoid damaging the magnets. The windshield wiper motor must not be struck or tapped with a hammer or other object.
Removal and Installation
1. Turn ignition switch to the run position. Turn on the turn signal and windshield wiper switch and cycle wipers to the mid-wipe position (straight-up) and turn off the ignition switch.
2. Disconnect battery ground cable.
3. Remove LH and RH windshield wiper pivot arms.
4. Remove cowl top extension to hood seal.
5. Remove cowl vent screens.
6. Remove four retaining bolts and washers and the cowl top extension.
7. Disconnect two wiring connectors from the windshield wiper motor.
8. Remove five retaining bolt and washer assemblies and one nut from the cowl top extension.
9. Lift the cowl top extension slightly to disengage the support bracket from the dash panel mounting stud, move the cowl top extension sideways about 50.8mm (2 inches) toward the passenger side and remove the cowl top extension from the vehicle.
10. Disconnect windshield wiper mounting arm and pivot shaft from the windshield wiper motor crankpin after removing the clip.
NOTE:
Check location of support bracket on cowl top extension.
11. Remove the windshield wiper motor's three retaining screws and remove windshield wiper motor from the cowl top extension.
CAUTION:
Before installing the windshield wiper pivot arm and windshield wiper blade assemblies to the windshield wiper mounting arm and pivot shaft, cycle windshield wiper motor and turn off turn signal and windshield wiper switch to ensure that the windshield wiper mounting arm and pivot shaft is in the park position. Refer to windshield wiper pivot arm «Removal and Installation» for installation procedure.
12. To install, reverse Removal procedure.
_________________________
I remember the procedure in my '93 being a royal PITA, but it's doable.
The manual says:
__________________
Windshield Wiper Motor
When installing the drive arm to a new windshield wiper motor follow the instructions included in the new windshield wiper motor kit.
CAUTION:
The internal permanent magnets used in the windshield wiper motor are a ceramic (glass-like) material. Care must be exercised in handling the windshield wiper motor to avoid damaging the magnets. The windshield wiper motor must not be struck or tapped with a hammer or other object.
Removal and Installation
1. Turn ignition switch to the run position. Turn on the turn signal and windshield wiper switch and cycle wipers to the mid-wipe position (straight-up) and turn off the ignition switch.
2. Disconnect battery ground cable.
3. Remove LH and RH windshield wiper pivot arms.
4. Remove cowl top extension to hood seal.
5. Remove cowl vent screens.
6. Remove four retaining bolts and washers and the cowl top extension.
7. Disconnect two wiring connectors from the windshield wiper motor.
8. Remove five retaining bolt and washer assemblies and one nut from the cowl top extension.
9. Lift the cowl top extension slightly to disengage the support bracket from the dash panel mounting stud, move the cowl top extension sideways about 50.8mm (2 inches) toward the passenger side and remove the cowl top extension from the vehicle.
10. Disconnect windshield wiper mounting arm and pivot shaft from the windshield wiper motor crankpin after removing the clip.
NOTE:
Check location of support bracket on cowl top extension.
11. Remove the windshield wiper motor's three retaining screws and remove windshield wiper motor from the cowl top extension.
CAUTION:
Before installing the windshield wiper pivot arm and windshield wiper blade assemblies to the windshield wiper mounting arm and pivot shaft, cycle windshield wiper motor and turn off turn signal and windshield wiper switch to ensure that the windshield wiper mounting arm and pivot shaft is in the park position. Refer to windshield wiper pivot arm «Removal and Installation» for installation procedure.
12. To install, reverse Removal procedure.
_________________________
I remember the procedure in my '93 being a royal PITA, but it's doable.
RE: windshield washer motor removal?
[div class="dcquote"][strong]Quote[/strong]
Anytime. I noticed you're from Charleston, WV? If you ever venture north to Morgantown, give a shout.
[/div]
your from morgantown, thats cool. i thought id be one of the only West Vians on here. ill probably be up in morgantown alil bit over the summer, i have some friends up there and ill probably be doin some shows in morgantown this summer... ill let ya know if and when im shootin through.
[div class="dcquote"][strong]Quote[/strong]
Anytime. I noticed you're from Charleston, WV? If you ever venture north to Morgantown, give a shout.
[/div]
your from morgantown, thats cool. i thought id be one of the only West Vians on here. ill probably be up in morgantown alil bit over the summer, i have some friends up there and ill probably be doin some shows in morgantown this summer... ill let ya know if and when im shootin through.