Search results

Hello. I've been doing a little more research and was going to order my chip today from Blue Oval Chips when the guy I spoke with advised me that Blue Oval's Valve body kits were far superior to the Bauman ReCal pro kit. Although i've done ALOT of research no one has spoken about the Blue Oval...

Hello. Just curious if anyone runs E-85 in their cars, or if there is any possible way to convert our cars so they can run straight E-85. Does anyone know if there's any way to do this on our cars? What what all would be required in doing this? Any comments/suggestions or ideas very much...

Hello. I just put in new Silverstar Hi beams, and the next night, i noticed my driver side HID was getting extremely weak. Maybe i bumped something on installation of the Hi beams that i'm unaware of. I had a feeling this time would come, and i'm ready to upgrade to the ones from the auction...

Hello. I just installed my new 4" Dynotech MMX Driveshaft. I pulled the entire tank for the installation, since i didn't pull my exhaust, just dropped it down. Well i only had 2 gallons of gas in it when i performed the driveshaft installation. So after i installed it I went and filled it...

Hello all. I'm wondering if anyone has used any of these products on their Mark VIII's and how well people like these products, and how they perform. I'm going to be needing a chip real soon, and I haven't really found much information on people using these products. I don't want a mail order...

Hello. I installed my 4" dynomax driveshaft tonight, and when i turn to the left very slightly it rubs my gas tank and makes a terrible noise. I've dropped the gas tank down and can see where it's rubbing, is there any solution for this? Has anyone else installed a 4" driveshaft and has any...

Hello all. I was thinking about getting the Stock replacement rotors for front and rear from SCP, the KVR rotors and pads. I was curious as if anyone else has used these, and how they perform/last/respond. I can tell i'm due for a new set of rotors, and i've never had crossdrilled rotors so...

Well last night I washed my car in the manual car wash and i spent extra time on the rims since there was a slight vibration. Well RIGHT after i washed my car i backed out of the car wash and when i stepped on the brakes to stop there was just a terrible vibrating noise comming from the front...

I bought silver stars for the high beams today. Got home and pulled the plastic pieces off, and attempted to twist the black things that hold the hi beam bulbs, didn't even budge. Then again it's kinda chilly out, but is this the correct way to remove them? They seem SOOO stiff and wouldn;t...

Hello. I FINALLY recieved my 4" Dynotech MMC driveshaft yesterday. They sent me the wrong one the first time, a 3.5". So i had to send it back and wait for the other one, they actually shipped the 4" before i got to ship the 3.5" back to them, good guys. Anyways, has anyone else installed...

Well, I had an appointment yesterday to have my tranny flushed, my Factory Tech seperator plate installed from scp, 3qt scp tranny pan/filter, but the tranny pan didn't come until today so i cancelled my appointment yesterday. The main reason i cancelled though, is because i'm unsure of this...

Hello. I just finished installing a new blend door actuator, and after it was all together i went cruising around, since i had heat :-) Anyways, i cruised around, just putting around town not really gettin on for about 45 mins, then all of a sudden i came to a stop and it died. Put it in...

Hello. I proceeded with the task this afternoon of changing my blend door actuator. I get everything apart, find out the tip of the gray arm is broken off, and i cant seem to pull it out, although i didn't try too hard. AND my blend door actuator was broken as well, i have the supposedly...

Hello. I ordered a 3qt tranny pan, the special filter, the factory tech valve body seperator plate shift kit, which is just the seperator plate and the "updated" accumulator pistons 1-2 and 3-4, which should be fine in my 98 but i'm replacing anyway. Just have a few questions on what else i...

Hello. I went to the exhaust shop today, a guy that has done my exhaust on every vehicle i own with pipes on. Well, I got the magnaflow X-Pipe resonator combo in one, and 2 bulletts off of summit, dynomax. I went to the exhaust shop today, and he put it up on the lift and we took a look at...

Hey everyone. I just purchased a set of underdrive pulleys, from SCP. I figure when i install them i may as well install a new water pump. I seen the High flow water pump on SHM, here's the link...