97LSC - work in progress
- Thread starter Mad1stGen
- Start date
black97lsc
New member
Thanks again. I did the same thing you did on my headunit; nice and solid!
Only picture I took is a very crappy phone pic but I did put one on each side.
Attachments
I second that!!
SCTBIRD1173
Mark my Bird!
Awesome Mike! I'm happy for you :thumbsup:
Mad1stGen
Booster
Cool exhaust set-up on the budget.
Keeping in mind Mike's thinning wallet, I modified the stock LSC exhuast to give a little more flow, and some sound to this car
At any point Mike decides to spend money on larger piping, the parts are here, already fitted
Two 45 deg mandrel elbows, and x-pipe installed in place of the 3rd cat/resonator.
Keeping in mind Mike's thinning wallet, I modified the stock LSC exhuast to give a little more flow, and some sound to this car
At any point Mike decides to spend money on larger piping, the parts are here, already fitted
Two 45 deg mandrel elbows, and x-pipe installed in place of the 3rd cat/resonator.
Attachments
Mad1stGen
Booster
Mufflers and adapters all welded and installed. Stock hangers reused from the old boat anchors.
I tucked the tips closer and out in relation to the cutouts, following the shape of the bumper cover.
The idea was to hide the mufflers as much as possible, while retain the somewhat stock appearance from the rear.
Where the hell is that replacement emission tray Mike ?
I tucked the tips closer and out in relation to the cutouts, following the shape of the bumper cover.
The idea was to hide the mufflers as much as possible, while retain the somewhat stock appearance from the rear.
Where the hell is that replacement emission tray Mike ?
Attachments
SCTBIRD1173
Mark my Bird!
Awesome work Jeremi!
Mike, can't wait to see/hear the "finished" product at Carlisle. Hope you're having Jeremi swap out that EVAP tray
Mike, can't wait to see/hear the "finished" product at Carlisle. Hope you're having Jeremi swap out that EVAP tray
SCTBIRD1173
Mark my Bird!
Mike I'm sure he'll come through for you. I've been very happy with my dealings with "Racebronco2" :thumbsup:
racebronco2
New member
It went out yesterday. It should take about a week to get. I went thru the trays i had and sent out the best one.haha yea I bought one from racebronco and had it shipped, hopefully
Mad1stGen
Booster
Kicking this car's azz one problem at a time ...
Emission tray finally replaced. Much better :thumbsup:
Then I did some digging around to find out what's causing somewhat of a weak upper RPM pull at WOT only, not at partial even 3/4 throttle.
I yanked on the passenger's side wheel well ground strap, and it fell apart in my hands (Thanks to Doug's post in the WTB section)
Of course, the motor mount stud came out in one piece with the nut still attached.
Some heat, clean up, new wire with soldered loops, back together in no time.
I also found the MAF to be in sad shape, so replaced it with a clean used unit.
Mike will need tires sooner than later :thumbsup:
Emission tray finally replaced. Much better :thumbsup:
Then I did some digging around to find out what's causing somewhat of a weak upper RPM pull at WOT only, not at partial even 3/4 throttle.
I yanked on the passenger's side wheel well ground strap, and it fell apart in my hands (Thanks to Doug's post in the WTB section
)Of course, the motor mount stud came out in one piece with the nut still attached.
Some heat, clean up, new wire with soldered loops, back together in no time.
I also found the MAF to be in sad shape, so replaced it with a clean used unit.
Mike will need tires sooner than later :thumbsup:
Attachments
my1995mark8
New member
Your work is mind boggling, i check this site all the time for updates. Nice work
