Search results

I should be an expert.. 3 MK8's, but the blue '93 has issues. The guy before me played with the wiring likely for one of those air ride controllers, but I fixed that. I put in a verified air compressor with a great vent solenoid, height sensors. The dang thing doesn't want to vent! I...

On Sale on an auction site we all know about: $995.00 shipped. Buy it now. Real Ford Racing, full kit, brand new. For those that are looking for some good high lift cams, with springs, valves, lifters, rockers etc. Good to 7K RPM. Read the reviews for your application. More than 10...

Need a Gen 1 Driver's Side, Dark Gray, Door Panel with the JBL speaker trim. Also the Trunk release switch, Fuel tank door release switch and associated trim. If you have a complete panel with all switches and trim pieces, that would be good too. Shipped to 20715 (Near DC). thanks, mark...

Have '93, 165K Miles, all stock, JBL, Factory Moon Roof, T-Control, CD Changer, etc. All Stock to start. What I did: 1) Trans-GO shift kit. One setting below "Hot Conterter. Chirps 2nd nicely. 2) '94 intake tube. The '93 Dimpled wonder doesn't work. Replace with a '94, Remove resonator...

This topic has been moved by the moderator of this forum. It can be found at: http://www.lincolnsclub.org/forum/dcboard.php?az=show_topic&forum=99&topic_id=320

Thought I recommend a nice stockish Gen 1 Mod. I know alot about these cars, if you buy ones, know what's involved.. i This is about Gen1's Only, don't know Gen 2's.. What's worn out if a Gen 1 original, plan on this unless you have an Arizona car that’s been garaged kept. 1) Upper Control...

Thought I'd get some opinions before I tear the intake off.. It's a '93, all stock, new plugs/wires, filters, no CE light etc. When you press the accelerator off of idle about 1/2 way, the engine sputters for like a second, then takes off. When it does respond, power is very good, this bogg is...

Any easy way to either default it off, or disable it permanently? mark

To all of you who trash the air ride for t-bird suspension. Air Ride with a tight front suspension cannot be beat for an ultra smooth, no rattle ride. I just replaced the upper control arms, front sway bar end links, inner/outter tie rods, and rear upper shock mounts. The air ride literally...

I cut out the center rail, drilled out the sample tube, JB welded in a brass tube, drilled out the MAF sensor "Hole", cleaned it all up and installed it. At first it idle d like it was way rich and trying to correct, but couldn't. I then chopped off the brass sample tube thinking it was...

I'm now the proud owner of both a '93 (165K) and a '94 (85K) matched pair. I'd like the groups comments with the few differences I've noticed: 1) The '93 has an intake tube (between MAF and Throttle body) which has several flow limiting "Bumps". Clearly the '94 tube which is smooth is far...

Few questions: 1) If I mount it up high, will it help with the start up oil pressure to limit the Gen 1 chain rattle? It would seem that maybe oil pressure at start up might be further delayed, causing the rattle to be really bad. My stock set up is fine without a cooler or remote filter (with...

Bought them off of EBay.. 4340 CNC I-Beams. Look really nice. 530 Grams, about 100 grams lighter than the standard Manley H-Beams. Only $330 a set, fine deal. Also found Mahle pistons for 499.00 with rings and pins from: http://mahlepistons.carshopinc.com They say in stock, but haven't...

Somebody told me that a Forged crank will weight significantly more than a Cast crank. Any truth to this, and if so, how much more? mark

I have my ASC sunroof out to be re-lubricated and cleaned out. I've heard that it will auto close if you leave the vehicle. It has two power wires (red and orange), but it won't work unless both power wires are connected to +12V. My wiring has been kludged at the fuse panel (as in fuse...

Is it as easy as I think? A WOT switch in series with a switch that opens when the IMRC's open? Should work fine. No Window switch needed. Discussion?? mark

What's the deal with this? It doesn't fit the stock Gen 1 MK8 pan because of the extensive scrapers in the MK8 pan. If I take out/ bend the MK8 pan scrapers, the Canton will be very far from the crank, and likely the screen will hit the bottom front of the pan anyway. I'm thinking I have to...

Bought the car in 2/03 with 87K miles, Installed TransGo shift kit (Hot Rod, No Torque Converter), did Accumulator 1-2 and 2-3 upgrades (they were already done however), and of course Mercon 5. Zero metal, and near zero "Sludge" in the pan when I changed it. Old fluid was bright red and didn't...

Anyone have a decent, low miles set for reasonable price? mark

Need a bunch of small, inconsequential things that are hard to ship like a headliner, front inner wheel well plastic splashguards etc. Would rather pick them up than have them shipped. Any glory? mark